Goodman GDVC80703B, Руководство по установке

Страница: 10 / 48

10
E E
E E
E
X X X X X T E R I O R T E R I O R T E R I O R T E R I O R T E R I O R M A S M A S M A S M A S M A SO N R O N R O N R O N R O N RY Y Y Y Y
C C
C C
C
H I M N E H I M N E H I M N E H I M N E H I M N EY Y Y Y Y S S S S S
- C - C
- C - C
- C
A A A A AT E G O R T E G O R T E G O R T E G O R T E G O RY Y Y Y Y
I F I F
I F I F
I F
U R N A U R N A U R N A U R N A U R N AC E S C E S C E S C E S C E S
O O
O O
O
N L N L N L N L N LY Y Y Y Y
CAN/CSA B149.1 and CAN/CSA B149.2 - latest editions and amend-
ments.
NO NO
NO NO NOTE:
TE:
TE: TE: TE: The vertical height of the Category I venting system must be
at least as great as the horizontal length of the venting system.
T
O PREVENT POSSIBLE PERSONAL INJURY OR DEATH DUE TO
ASPHYXIATION
,
COMMON VENTING WITH OTHER MANUFACTURER
’
S
INDUCED DRAFT APPLIANCES IS NOT ALLOWED
.
WARNING
The minimum vent diameter for the Category I venting system is as
shown:
UPFLOW COUNTERFLOW
70 4 inch 4 inch
90 4 inch 4 inch
115 5 inch 4 inch
MINIMUM VENT
MODEL
Under some conditions, larger vents than those shown above may
be required or allowed.
When an existing furnace is removed from a
venting system serving other appliances , the venting system may be
too large to properly vent the remaining attached appliances.
Upflow or Horizontal units Upflow or Horizontal units Upflow or Horizontal units Upflow or Horizontal units Upflow or Horizontal units are shipped with the induced draft
blower discharging from the top of the furnace. (“Top” is as viewed
for an upflow installation.) The induced draft blower can be rotated
90 degrees for Category I venting. For horizontal installations, a
four inch single wall pipe can be used to extend the induced draft
blower outlet 1/2” beyond the furnace cabinet. THIS PR
THIS PR THIS PR THIS PR THIS PRODUC ODUC ODUC ODUC ODUCT IS T IS T IS T IS T IS
NO NO NO NO NOT DESIGNED FOR C T DESIGNED FOR C T DESIGNED FOR C T DESIGNED FOR C T DESIGNED FOR COUNTER OUNTER OUNTER OUNTER OUNTERCL CL CL CL CLOCK OCK OCK OCK OCKWISE INDUCED DR WISE INDUCED DR WISE INDUCED DR WISE INDUCED DR WISE INDUCED DRAFT AFT AFT AFT AFT
BL BL BL BL BLOWER R OWER R OWER R OWER R OWER RO O O O OT T T T TA A A A ATION. TION. TION. TION. TION.
Vent the furnace in accordance with the National Fuel Gas Code
NFPA 54/ANSI Z223.1 - latest edition. In Canada, vent the furnace
in accordance with the National Standard of Canada, CAN/CSA
B149.1 and CAN/CSA B149.2 - latest editions and amendments.
Venting Venting
Venting Venting Venting
THIS FURNACE IS NOT DESIGN CERTIFIED TO BE HORIZONTALLY
VENTED.
To rotate the induced draft blower clockwise, you will need to pur-
chase one (0270F01119) chimney transition bottom kit.
1. Disconnect electrical power from the furnace.
2. Disconnect the induced draft blower power leads, flue pipe,
and pressure switch tubing.
3. Remove the round cutout from the right side of the wrapper.
4. Remove and save the four screws that fasten the induced
draft blower to the flue collector box.
5. Remove and save the three screws that hold the chimney
assembly to the induced draft blower.
6. Remove and save the four screws that fasten the chimney
top to the chimney bottom.
7. Remove the chimney transition bottom from the transition
bottom kit.
8. Install the chimney top with the four screws retained from
step 6 onto the new chimney transition bottom from the
transition bottom kit.
9. Install chimney assembly with the three screws retained
from step 5 onto the induced draft blower.
10. Reinstall the induced draft blower rotating it 90 degrees
clockwise from the original upflow configuration using the
four screws retained in step 3. Ensure the gasket located
between the induced draft blower and the collector box is
rotated accordingly.
11. Reconnect the induced draft blower power leads. NOTE: If
the wires are not long enough, pull extra wire from the wire
bundle in the blower compartment.
12. Reconnect the flue pipe, and the pressure switch tubing.
Ensure that all wires and the pressure switch tubing is at
least one inch from the flue pipe, or any other hot surface.
13. Restore power to furnace.
Counterflow units Counterflow units Counterflow units Counterflow units Counterflow units are shipped with the induced draft blower dis-
charging from the top of the furnace. (“Top” as viewed for a coun-
terflow installation.)
Vent the furnace in accordance with the National Fuel Gas Code
NFPA54/ANSI Z223.1-latest edition. In Canada, vent the furnace in
accordance with the national standard of Canada, CAN/CSA B149.1
and CAN/CSA B149.2- latest editions and amendments.
N
EVER ALLOW THE PRODUCTS OF COMBUSTION
,
INCLUDING CARBON
MONOXIDE
,
TO ENTER THE RETURN DUCTWORK OR CIRCULATION AIR
SUPPLY
.
WARNING
E E
E E E
X X X X XTERIOR TERIOR TERIOR TERIOR TERIOR
M M
M M M
ASONR ASONR ASONR ASONR ASONRY Y Y Y Y
C C
C C C
HIMNE HIMNE HIMNE HIMNE HIMNEY Y Y Y YS S S S S
( (
( ( (C
C
C C C
A A A A ATEGOR TEGOR TEGOR TEGOR TEGORY Y Y Y Y
I F I F
I F I F I F
URNA URNA URNA URNA URNACES CES CES CES CES
O O
O O O
NL NL NL NL NLY Y Y Y Y
)))))
An exterior masonry chimney is defined as a “Masonry” chimney
exposed to the outdoors on one or more sides below the roof line.”
The ability to use a clay lined masonry chimney depends on a pa-
rameter not associated with interior chimneys. This variable is the
geographic location of the installation. Researchers have discov-
ered that the winter design temperatures have a direct impact on
the suitability of this type of venting. In most situations, the existing
masonry chimneys will require a properly sized metallic liner.