GE Solar 8000M/i Скачать руководство пользователя страница 149

Страница: 149 / 192

2026265-075C

Solar 8000M/i patient monitor

7-9

Field replaceable units:

Disassembly

Power supply

1. Remove cover.

2. Disconnect cable harness between circuit boards.

3. Remove three screws that secure the aluminum mounting bracket to

the chassis.

4. At the top rear of the unit, remove the two screws closest to the AC

power inlet.

5. Slide the power supply forward to clear the equipotential post and

lift out the power supply.

Processor PCB

Before replacing the processor pcb

Before replacing the processor pcb, write down the following information:
(All settings are viewable in Boot Code except for unit type. See

“Boot

loader or boot code”

on page 5-2.)

Current language (set in Boot Code)

Bed number (set in Main Code)

Unit name (set in Main Code)

Subnet masks 1 and 2 (set in Boot Code)

Gateway addresses 1 and 2 (set in Boot Code)

Internet (IP) addresses 1 and 2 (set in Boot Code)

Product type (Unity View or Solar 8000M/i) (set in Boot Code)

Line frequency (50/60 Hz) (set in Boot Code)

Sync pulse height and width (set in Boot Code)

Hi Res trends (enabled/disabled) (set in Boot Code)

Software feature level (set in Boot Code)

Country selection (set in Boot Code)

Unit type (adult, OR, neonatal) (set in Main Code)

Replace the processor pcb

1. Remove the cover. (See

“Cover”

on page 7-8.)

If your unit has a Solar 8000M/i patient monitor to Patient Data
Module (SPA), then:

a. Remove 2 screws from the SPA.

b. Disconnect the SPA from the TRAMNET 1 port.

c. Remove the M-Port ethernet cable from the SPA and the M-Port.

NOTE

The above items are no longer needed with the new processor
pcb.

Содержание Solar 8000M/i

































































































































































































Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды

GE Solar 8000M/i, Руководство по обслуживанию

Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды