manualshive.com logo in svg

GE Solar 8000M/i, Руководство по обслуживанию

Скачайте бесплатно сервисный мануал для GE Solar 8000M/i на manualshive.com. Получите подробные инструкции по обслуживанию и ремонту этого продукта высокого качества. Не упустите возможность загрузить руководство в формате PDF прямо сейчас, чтобы легко проводить техническое обслуживание вашего оборудования.

Поделиться
Скачать
background image

2026265-075C

Solar 8000M/i patient monitor

5-13

Troubleshooting: 

Troubleshooting procedure

Problems and solutions

Problem

Possible Reason and Solution

The display is blank.

The video display has no power. Verify that the display’s power indicator is illuminated.

The patient monitor has no power. Verify that the patient monitor’s power indicator is illuminated.

The video display is not properly connected to the patient monitor. Verify that the correct cable 
connects the video display to one of the 4 video ports on the patient monitor.

The display was turned off via the 

Display On/Off

 button on the keypad/remote control. Press the 

Display On/Off

 button on the keypad/remote control.

Hardware failure. 
1. The SDRAM test performed by Boot Code failed.Check the 

LS6

 LED (I’m OK). If the SDRAM test 

failed, it will continually flash error codes.

„

Error codes always start with 3 very short pulses in quick succession.

„

Binary 1s are long ON pulses.

„

Binary 0s are short ON pulses.

„

The first digit is the most significant.

„

There are 6 binary digits per error code.

„

A short pause occurs between the first 4 binary digits and the last 2 binary digits.

If you observe error codes, replace the processor pcb.
2. Boot Code not loaded properly or is corrupt. This may be the case if the I’m OK LED is stuck ON or 

OFF. Replace the processor pcb.

3. Power supply failure. Replace the power supply.
4. Loose connections to power supply. Tighten connections.
5. Excessive loading on external connector due to malfunctioning peripheral device. Isolate and replace 

the malfunctioning device.

6. Other. Replace the power supply.
7. Power supply replaced, but display still doesn’t work. Replace processor pcb.

Boot Code starts, but Main 

Code does not.

1. Check the boot banner for hardware test results. The following information is available:

„

SRAM test results (passed or failed)

„

SDRAM test results (passed or failed)

„

Main flash check (passed or failed)

„

Boot flash check (passed or failed)

„

Real time clock (is running or failed)

If any of the above is failed, then Boot Code refuses to run the Main Code. Cycle power on the patient 
monitor and it may correct itself.
2. Attempt to start Main Code via the “return to Patient Monitoring”. One of the following may be the 

problem:

„

Main Code not loaded. Follow the software installation instructions to download Main Code. 
(These instructions ship with the software upgrade kit.)

„

Main Code and Boot Code not compatible. Follow the software installation instructions to update 
the Boot Code to a version compatible with the Main Code. (These instructions ship with the 
software upgrade kit.)

3. If the problem is still not corrected, replace the processor pcb.

The quality of the display is 

not good.

Check the connection between the video display and the patient monitor and correct, if necessary, or 
replace the video display with a known good one. If the problem is not corrected, replace the processor 
pcb.

Содержание Solar 8000M/i

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar 8000M/i

GE TruSat User Manual preview
TruSat
Бренд: GE Страницы: 43
GE Responder AED Service Manual preview
Responder AED
Бренд: GE Страницы: 37
GE Senographe DS Operator'S Manual preview
Senographe DS
Бренд: GE Страницы: 210
GE MAC 5000 Field Service Manual preview
MAC 5000
Бренд: GE Страницы: 160
GE MAC 1600 Service Manual preview
MAC 1600
Бренд: GE Страницы: 146
GE Dash 2500 Quick Manual preview
Dash 2500
Бренд: GE Страницы: 6
GE ApexPro Manual preview
ApexPro
Бренд: GE Страницы: 27
GE Voluson 730 Manual preview
Voluson 730
Бренд: GE Страницы: 4
Panasonic AJSPD850P - P2 DECK Operating Instructions Manual preview
AJSPD850P - P2 DECK
Бренд: Panasonic Страницы: 73
Panasonic LP-GS Series Serial Communication Command Manual preview
LP-GS Series
Бренд: Panasonic Страницы: 180
Raymarine RS232 Owner'S Handbook Manual preview
RS232
Бренд: Raymarine Страницы: 24
Hansen P4 Installation Manual preview
P4
Бренд: Hansen Страницы: 72
AAT SOLO Original User Manual preview
SOLO
Бренд: AAT Страницы: 16
AAT S-max Translation Of The Original User Manual preview
S-max
Бренд: AAT Страницы: 40
Dairy Tech Platinum Series Operator'S Manual preview
Platinum Series
Бренд: Dairy Tech Страницы: 38
H&S M6 Parts List And Operator'S Instructions preview
M6
Бренд: H&S Страницы: 34
QAL Medical 480 Service And Technical Manual preview
480
Бренд: QAL Medical Страницы: 42
Bard PowerGlide Patient Manual preview
PowerGlide
Бренд: Bard Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды