GE Solar 8000M/i Скачать руководство пользователя страница 74

Страница: 74 / 192

4-22

Solar 8000M/i patient monitor

2026265-075C

Maintenance and checkout:

Checkout procedure

Parameter tests

ECG functions

These procedures test the following:

Lead and heart rate information displays properly.

QRS tone sounds.

Pacemaker mode displays in ECG parameter box.

Calibration pulses display with correct amplitude.

1. Set up the simulator:

Heart rate to 80 bpm.

ECG amplitude to 1.0 mV.

2. Attach the patient cable and leadwires between the ECG connector

on the acquisition device and the leadwire connectors on the patient
simulator.

3. Set up the patient monitor:

a. Go to

MORE MENUS

MONITOR SETUP

PARAMETERS

ON/OFF

and turn off all parameters except

ECG

b. In

MONITOR SETUP

select

WAVEFORMS ON/OFF

and set

leads in the following order:

Waveform 1 =

Waveform 2 =

Waveform 3 =

III

Waveform 4 =

Waveform 5 =

AVL

Waveform 6 =

AVF

c. From the

ECG

Menu, select

MORE ECG

QRS VOLUME:

and

set to the desired volume percentage.

4. Admit a patient into patient monitor. (

MORE MENUS

ADMIT

MENU

ADMIT PATIENT

)

5. Check that the following conditions are true:

The monitor displays ECG lead II, and it is noise-free.

The patient monitor displays an 80 ±1 bpm heart rate.

The patient monitor QRS audible tone sounds with each QRS
complex.

6. Make sure all six ECG leads are available for display and are noise-

free.

7. At the patient monitor, select the ECG parameter window to display

the ECG menu at the bottom of the screen.

8. Select

PACE 1:

PACE 2:

9. Inject an asychronous pacemaker pulse with the simulator.

Содержание Solar 8000M/i

































































































































































































Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды

GE Solar 8000M/i, Руководство по обслуживанию

Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды