GE Solar 8000M/i Скачать руководство пользователя страница 77

Страница: 77 / 192

2026265-075C

Solar 8000M/i patient monitor

4-25

Maintenance and checkout:

Checkout procedure

Cardiac output functions

1. Connect the cardiac output cable adapter to the

Temp/CO

connector

of the acquisition device.

2. Connect the cardiac output adapter to the cardiac output cable

adapter and to the simulator.

3. At the patient monitor, go to

MENUS

⇒

4. Set up the monitor:

Set

AUTO MODE:

Set

INJECT TEMP:

BATH

Set

SIZE:

Set

INJECT VOL:

10CC

Set

COMPUTATIONAL CONSTANT:

0.540

5. Select cardiac output menu corresponding to the injectate

temperature. (

)

6. Set the adapter and simulator to

0°

. Verify that the IT value on the

lower left of the display matches the input.

When computing is complete, the

reading on the patient monitor

should read approximately ±5% of simulated value.

7. Repeat this test with the adapter and simulator set to

24°

and the

COMPUTATIONAL CONSTANT:

set to

0.595

The computed output should be ±5% of simulated value.

SpO

functions (Masimo)

1. Connect the Masimo SpO2 tester cable to the SpO2 sensor adapter

cable.

2. Connect the SpO2 adapter cable to the SpO2 connector on the

acquisition device.

3. Turn the patient monitor on.

4. Verify the following are displayed at the patient monitor: (It might

be necessary to turn the SpO

parameter on.)

A waveform with an SpO

label.

An SpO

% reading between 78- 84%.

A PRR reading between 60 and 62 beats per minute.

5. Disconnect the simulator cable from the acquisition device.

SpO

functions (Nellcor OxiMax)

1. Verify that 2 AA alkaline batteries are installed in the NELLCOR

SRC-MAX Pulse Oximetry functional tester.

2. Connect the SRC-MAX to the

SpO

connector on the module.

3. On the SRC-MAX, verify that the

and

RED

LED indicators are

both lit.

Содержание Solar 8000M/i

































































































































































































Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды

GE Solar 8000M/i, Руководство по обслуживанию

Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды