GE Solar 8000M/i Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 192

background image

5-2

Solar 8000M/i patient monitor

2026265-075C

Troubleshooting:

Terms used

Terms used

Listed and defined below are terms used in this chapter.

Abort (main code)

This is a Main Code menu selection that may appear on the monitor
during software downloads from the monitor

SERVICE MODE

menu.

ABORT

causes the download to stop by pushing the

TRIM KNOB

control.

Boot loader or boot code

The Boot Loader or Boot Code is used to download software. Entering the
Boot Code does not erase any memory, but downloading new software
will erase protected memory. To activate the Boot Code, perform the
following.

1. Hold down

NBP Go/Stop

and

Zero All

.

2. Press and release the

TRIM KNOB

control.

3. Keep holding

NBP Go/Stop

and

Zero All

until the Boot Code

information appears on the display.

Cold start

A cold start is used only in extreme circumstances. It erases the
protected memory, language, unit name and bed number; automatically
discharges the patient; and restores factory defaults. Ethernet address,
internet address, software feature level, and CRG trend option remain
unchanged.

1. Hold down

NBP Go/Stop

and

Zero All

.

2. Press and release the

TRIM KNOB

control and keep holding

NBP

Go/Stop

and

Zero All

.

3. When the monitor resets and the display goes blank, press and hold

Display On/Off

(in addition to

NBP Go/Stop

and

Zero All

)

until

the message “

performing cold start

” appears on the display.

NOTE

If the Boot Code information appears before the message
“

performing cold start”

appears, begin the cold start again.

Continue (main code)

CONTINUE

is a Main Code menu selection that appears after a

successful software download. It allows the user to continue downloading
other files without resetting the monitor.

«
...
92
93
94
95
96
...
»

Содержание Solar 8000M/i

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Solar 8000M/i

Бренд: Oemtools Страницы: 4

Бренд: NEC Страницы: 44

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: Bard Страницы: 144

Бренд: GALBIATI Страницы: 8

Бренд: Vahva Jussi Страницы: 9

FreeStyle Comfort

Бренд: CAIRE Страницы: 33

Бренд: Unitary products group Страницы: 28

Бренд: Garelick Страницы: 4

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

QuickSlide HemaPRO

Бренд: Hardy Diagnostics Страницы: 2

Бренд: Hardt Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды