GE PanaFlow HT Скачать руководство пользователя страница 75

Страница: 75 / 163

PanaFlow HT User’s Manual

Chapter 3. Initial Setup and Programming

3.7.3 Digital Output C (cont.)

3.7.3d Setting the Alarm (cont.)

To check and/or change the type of alarm measure, select

Measurement

and

press

[



]

. A screen similar to the following appears.

Select the type of measure desired, press

[



]

, and the screen returns to the

previous display.

The Alarm Value is the threshold that trips the alarm. (This parameter does not
apply to Fault Alarms.) To check and/or change the alarm value, select

Alarm

Value

and press

[



]

. A screen similar to the following appears.

Press

[



]

again, and a screen similar to the following appears.

Note:

The units that appear will be the units selected in “Flow Units” on

page 43.

Use the [



] or [



] arrow key to change the

Alarm Value

setting. Press

[



]

to save

the number and press [



]

to return to the previous screen.

Содержание PanaFlow HT




































































































































































Результаты поиска

Содержание PanaFlow HT

Отзывы:

Бренды по названию

Популярные бренды

GE PanaFlow HT, Руководство пользователя

Результаты поиска

Содержание PanaFlow HT

Отзывы:

Бренды по названию

Популярные бренды