manualshive.com logo in svg

GE PanaFlow HT, Руководство пользователя

Поделиться
Скачать
GE PanaFlow HT Скачать руководство пользователя страница 65

PanaFlow HT User’s Manual

55

Chapter 3. Initial Setup and Programming

3.7.2 Analog Output B (Non-SIL) (cont.)

3.7.2b Setting the Analog Measurements

 To set up the SIL analog output, select 

Analog Output (SIL)

 and press 

[

]

. The 

following screen appears.

Note: 

If the 

General User

 password is used, the 

Analog Output (SIL)

 is not 

accessible.

Select 

Measurement

 and press 

[

]

. The following screen appears.

In the 

Output (SIL) Analog

 menu, select the type of analog output to be used, and 

press 

[

]

. The screen returns to the previous display.

3.7.2c Setting the Base Value and Full Value

 Base Value is the flow rate represented by 4 mA, and Full Value is the flow rate 
represented by 20 mA.In the 

Analog Output

 menu, select 

Base Value

 or 

Full 

Value

 and press 

[

]

 A screen similar to the following appears.

Press 

[

]

 again and a screen similar to the following appears.

Note: 

The units that appear will be the units selected in “Flow Units” on 

page 43.

Use the[

] and [

] arrow key to select the digit to be changed, use the [

] or 

[

] arrow key to change the 

Base Value

 or 

Full Value

 setting, and press 

[

].

 

Repeat these steps to set the 

Full Value 

setting.

 

Press

 [

]

 to return to the 

Analog 

Output

 menu.

I/O / SIL Out
   Analog Output (SIL/HART)
   Analog Output B
   Digital Output
   Modbus/Service Port

Analog Output B (NSIL)

Measurement

   

Velocity

Volumetric (Std)

Volumetric (Act)

Mass

0

Содержание PanaFlow HT




































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды