GE PanaFlow HT Скачать руководство пользователя страница 59

Страница: 59 / 163

PanaFlow HT User’s Manual

Chapter 3. Initial Setup and Programming

3.6.4 Password

3.6.4a General User

This option is used to change the General User password to a custom value. To set
up a password, under

User Preference

, use the [



] or [



] arrow key to select

Password

and press

[



]

. The following screen appears.

Note:

If the password used to access programming was

Gen User

, only

Gen User

will appear on the next screen.

To provide a general user password, select

Gen User,

press

[



]

, and a screen

similar to the following appears.

Note:

If the access level is General User, the SIL User option will not be

available. Also, a SIL User will be able to reset the General User password.

Use the [



] or [



] arrow key to change the digit value and press

[



]

. Press the

[



]

key to return to the

UserPref/Password

screen.

3.6.4b SIL User

Use the above procedure to change a

SIL User

password from its default.

Note:

If the password used to access programming was

Gen User

SIL User

is not accessible.

Note:

If the SIL User password is lost, a service engineer must reset the password.

9999

Содержание PanaFlow HT




































































































































































Результаты поиска

Содержание PanaFlow HT

Отзывы:

Бренды по названию

Популярные бренды

GE PanaFlow HT, Руководство пользователя

Результаты поиска

Содержание PanaFlow HT

Отзывы:

Бренды по названию

Популярные бренды