manualshive.com logo in svg

GE PanaFlow HT, Руководство пользователя

Поделиться
Скачать
GE PanaFlow HT Скачать руководство пользователя страница 28

Chapter 2. Installation

18

PanaFlow HT User’s Manual

2.5.3d Wiring as Control Output

The purpose of the Control Output is to generate a signal that can be used to control an external device based on a 
totalized measurement in the flowmeter. The Control State can be set to Normally Open or Normally Closed. The 
setting depends on the device being connected to the control output. The Control State indicates whether the Operator 
wants that switch to be Open or Closed until the point where the measured total threshold is reached. Once the flow 
totals reach the threshold level, the meter will switch the Control Output to the opposite state.  If the system calls for 
the Control to be Open (0 VDC) until a certain flow level is reached, the Operator should set the Control to Normally 
Open. At the measured threshold, the flowmeter will change the Control to Closed (5 VDC). If the system calls for the 
Control to be closed until a certain flow level is reached, the Operator should set the Control to Normally Closed. At 
the measured threshold, the flowmeter will change the Control to Open. Connect each control output in accordance 
with the wiring instructions shown on the label inside of the rear cover and below on Figure 14.

Figure 14: Control Output Connections

XMT900

-       +

Control Device

XMT900

-       +

Control Device

XMT900

-       +

Control Device

XMT900

-       +

Control Device

Normally Open Configuration
+NO
-C

Conventional Not 
Triggered State

Normally Closed Configuration
+NC
-C Wiring

Conventional Not Triggered State

Conventional Triggered State

Conventional Triggered State

Содержание PanaFlow HT




































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды