Furukawa Unic URW376C4U -T Series Скачать руководство пользователя страница 97

Страница: 97 / 156

12-5

MAINTENANCE AND INSPECTION OF CARRIER

Check engine oil quantity before starting the
engine with the crawler crane parked on a flat
ground.
If the engine has been started, check the oil
level after at least more than 5 minutes when
the engine had been stopped.

◆

Check for engine oil quantity
/ Filling up

★

Wipe up spilled oil thoroughly after filling it up as it may cause the

fire.

WARNING

★

Replace engine oil and fuel filter element after 100 hours (1 month) of

operation, then every 250-hour operation (3 months) thereafter.

CAUTION

• Extract the oil level gauge and wipe it off

with a piece of clean rag.

Insert the gauge again slowly then extract
it to check the level wet with oil.
(Check the oil for contamination and viscos-
ity at the same time.)

• If oil level is found too low, supply it from

the filling port.

Filling port

Oil level gauge

Upper limit

Lower limit

Содержание URW376C4U -T Series





























































































































































Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды

Furukawa Unic URW376C4U -T Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды