Furukawa Unic URW376C4U -T Series Скачать руководство пользователя страница 115

Страница: 115 / 156

12-23

MAINTENANCE AND INSPECTION OF CARRIER

Carry out “Inspection and Maintenance which is to be carried out every 250/ 500
hours or 3/6 months”, illustrated in previous sections together with this inspection
and maintenance.

Inspection and Maintenance which is to

be carried out every 1000 hours or 12 months

◆

Replacement of hydraulic oil

in the oil tank and cleaning of
suction strainer

★

Do not rush to start replacement of oil as it is heated to a high tem-

perature immediately after the engine has been stopped.
Replace the oil after the oil has cooled down.

★

Remove the cap on the filling port after confirming that oil tempera-

ture has dropped.

★

Wipe up spilled oil thoroughly after replacement to avoid an acciden-

tal fire.

Replace hydraulic oil together with the line
filter element at the same time.

Filling port cap

WARNING

Remove the drain plug located on the bot-
tom of hydraulic oil tank to drain oil.

Capacity of hydraulic oil tank:19.8gal(75 liters).
Prepare a container having enough capacity for
holding as much as 19.8gal(75 liters).

Park the crawler on a flat ground to stop
the engine.

Move each operation lever to release
the internal pressure in the hydraulic

system.

Remove the cap on the filling port slow-
ly.

Place a container under the drain plug to
receive oil being drained.

Drain plug

Содержание URW376C4U -T Series





























































































































































Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды

Furukawa Unic URW376C4U -T Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды