Furukawa Unic URW376C4U -T Series Скачать руководство пользователя страница 102

Страница: 102 / 156

12-10

MAINTENANCE AND INSPECTION OF CARRIER

Standard: 1.06~1.38in.(27~35mm)
Adjust if less than 0.78in.(20mm)

◆

Check for rubber crawler
/ Adjustment

★

Do not check rubber crawler tension with the crane body raised

above

the

ground.

It is very dangerous because an accidental fall of the crane may
happen

during

inspection.

Be sure to carry out tension check with the crane touched the ground.

Mark “BS”

■

Inspection

★

Adjust the tension after 30

hours of operation if the new rub-
ber crawler has been mounted.

Lug

Height of lug

• Replace the rubber crawler when the lug

height becomes less than 1/8in.(3mm).

WARNING

Check the rubber crawler for wear and for
tension as the wear varies according to oper-
ating and ground conditions.
• Check rubber crawler tension with the seam

of rubber crawler positioned at the cen-
ter between wheels at the other side of the
ground.

• Putting the mark “BS” at the center between

the wheels on ground side allows the seam
to be positioned at the center of wheels
on the other side.

Wrong positioning shows larger slack of
rubber crawler than the proper tension
which results in re-adjustment.

• If the tension is too tight, it shortens service

life of wheel sprocket.

CAUTION

Содержание URW376C4U -T Series





























































































































































Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды

Furukawa Unic URW376C4U -T Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды