Furukawa Unic URW376C4U -T Series Скачать руководство пользователя страница 95

Страница: 95 / 156

12-3

MAINTENANCE AND INSPECTION OF CARRIER

◆

Check for remaining fuel quantity
/ Draining water

★

Fuel (diesel fuel oil) is highly inflammable.

Do not smoke and bring a fire source close to the fuel when refueling
and draining sediment.

★

Wipe up spilled fuel thoroughly after refueling as it may cause the

fire.

Fuel strainer

WARNING

• Carry out air bleeding in the fuel system

by referring to the section “Precautions
before operation (air-bleeding pro-
cedures)” on page 10-5.

Fuel filling port is located on the right side
at the rear of the crane.

• Check the side gauge that fuel is filled

enough before starting inspection.

• When refueling, prevent dirt and dust from

entering the filling port and be sure to put
the strainer of fuel tank in the port.

• Lock the cap after the refuel.

Fill up the tank after completion of car-
rier

operation.

Fuel tank capacity : 10.6gal(40 liters)

Fuel filling port

Side gauge

Содержание URW376C4U -T Series





























































































































































Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды

Furukawa Unic URW376C4U -T Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды