Furukawa Unic URW376C4U -T Series Скачать руководство пользователя страница 67

Страница: 67 / 156

10-9

HOW TO OPERATE CARRIER

How to Crawl

★

Start the crane crawling after the safety around the crawler has been

confirmed and make a sign when crawling the crane.

★

Keep anyone away from the crane.

★

Pay special attention when turning left because the left side of crawl-

er will be in your blind spot.

★

Crawl the crane as slowly as possible while making a turn.

★

Run the crane slowly when making a quick turn and crawling on a

rough road.

★

Lock the crawling lever with the interlock for crane-crawl operation

and stop the engine running before leaving from the crane.

★

When parking the crane on the street is unavoidable, set up safety

devices such as a sign, a barricade, and a blinking light so that passing
of other vehicles and pedestrians may not be disturbed.

★

Put a pallet against the rubber crawler when parking the crane for a

long period of time.

★

Do not park the crane over a place where withered grass or straw,

which

flammable,

spread.

This may cause a fire by heat of exhaust pipe or exhaust fume.

★

When crawling the crane on a water filled area, observe to crawl it

within allowable depth of water.

★

In case where the machine is forced to turn on the spot (spin turn), be

sure to stop the movement of the machine first, allow the engine to run
at a low speed to make it turn slowly and gently.

An abrupt turning not only damages the rubber crawler badly but also
causes the machine to bounce from which may invite a very dangerous
situation.

WARNING

Содержание URW376C4U -T Series





























































































































































Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды

Furukawa Unic URW376C4U -T Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды