Furukawa Unic URW376C4U -T Series Скачать руководство пользователя страница 48

Страница: 48 / 156

9-12

DESCRIPTION OF EACH CONTROL DEVICE

If an alarm sounds intermittently due to
decrease of ground reaction against out-

riggers, operating the crane to safer side.
If the ground reaction against the outrigger
decreases further, the crane makes an auto-
matic

stop.

In this case, faster operating speed can make
the crane to be overturned to which must pay
attention.

Observe that the crane shall not be
operated within the prohibited range in

extending outriggers.

The turn over prevention device will not func-
tion safely when the crane is operated within
the prohibited range.

Keep the “ON-OFF” switch for alarm
buzzer turning ON unless there is any

special reason.

As a rule, set up the crane on a flat and
solid ground to operate it with the out-

riggers extended to their extremes, with the
truck kept level, and with the rubber crawler
lifted up by approx. 2in(50mm) above the
ground.

Содержание URW376C4U -T Series





























































































































































Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды

Furukawa Unic URW376C4U -T Series, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание URW376C4U -T Series

Отзывы:

Бренды по названию

Популярные бренды