Fujitsu F2MCTM-16LX Скачать руководство пользователя

Страница: 457 / 682

441

CHAPTER 20 LIN-UART

20.8

Notes on Using LIN-UART

Notes on using LIN-UART are given below.

■

Notes on Using LIN-UART

●

Enabling operations

In LIN-UART, the serial control register (SCR) has TXE (transmission) and RXE (reception) operation

enable bits. Both, transmission and reception operations, must be enabled before the communication starts

because they have been disabled as the default value (initial value). The operation can also be canceled by

disabling these bits.

●

Communication mode setting

Set the communication mode while the system is not operating. If the mode is changed during transmission

or reception, the transmission or reception is stopped and possible data will be lost.

●

Transmission interrupt enabling timing

The default (initial value) of the transmission data empty flag bit (SSR: TDRE) is "1" (no transmission data

and transmission data write enable state). A transmission interrupt request is generated as soon as the

transmission interrupt request is enabled (SSR: TIE=1). Be sure to set the TIE flag to "1" after setting the

transmission data to avoid an immediate interrupt.

●

Changing operation settings

It is strongly recommended to reset LIN-UART after changing operation settings. Particularly if (for

example) start-/stop-bits added to or removed from the data format.

If settings in the serial mode register (SMR) are desired, it is not useful to set the UPCL bit to 1 at the same

time to reset LIN-UART. The correct operation settings are not guaranteed in this case. Thus it is

recommended to set the bits of the SMR and then to reset them again plus the UPCL bit.

●

Using LIN operation mode 3

The LIN features are available in mode 3 (transmitting, receiving synch break), but using mode 3 sets the

UART data format automatically to LIN format (8N1, LSB first). Note that the length of the synch break

for transmission is variable but for reception it is fixed 11-bit time.

●

LIN slave settings

Set the baud rate before receiving the first LIN synch break for the slave operation. This is needed to detect

the minimum of 13-bit time of a LIN synch break surely.

●

Software compatibility

Although this LIN-UART is similar to other LIN-UART in other microcontrollers, it is not software

compatible to them. The programming models may be the same, but the structure of the registers differ.

Furthermore, the setting of the baud rate is now determined by a reload value instead of selecting a

Содержание F2MCTM-16LX











































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание F2MCTM-16LX

Отзывы:

Похожие инструкции для F2MCTM-16LX

Бренды по названию

Популярные бренды

Fujitsu F2MCTM-16LX, Руководство по оборудованию

Результаты поиска

Содержание F2MCTM-16LX

Отзывы:

Похожие инструкции для F2MCTM-16LX

Бренды по названию

Популярные бренды