Fujitsu F2MCTM-16LX Скачать руководство пользователя

Страница: 383 / 682

367

CHAPTER 18 8-/10-BIT A/D CONVERTER

18.5.5

A/D-converted Data Protection Function

A/D conversion with the output of an interrupt request enabled activates the A/D
conversion data protection function.

■

A/D-converted Data Protection Function in 8-/10-bit A/D Converter

The 8-/10-bit A/D converter has only one A/D data register (ADCR) where A/D-converted data is stored.

When the A/D conversion results are determined after the termination of A/D conversion, data in the A/D

data register is rewritten. Therefore, the A/D conversion results may be lost if the A/D conversion results

already stored are not read before data in the A/D data register is rewritten. The A/D-converted data

protection function in the 8-/10-bit A/D converter is activated to prevent data loss. This function

automatically causes A/D conversion to pause when an interrupt request is generated (ADCS:INT = 1) with

an interrupt request enabled (ADCS:INTE = 1).

●

A/D-converted data protection function when EI

OS not used

•

When the A/D conversion results are stored in the A/D data register (ADCR) after the analog input is

A/D-converted, the interrupt request flag bit in the A/D control status register (ADCS: INT) is set to "1".

•

The A/D conversion stops for data protection immediately before new data is overwritten to the A/D

data register if the interrupt request is enabled (ADCS: INTE = 1) while the interrupt request flag bit set

at termination of previous A/D conversion is set at the point that next A/D conversion is terminated.

•

When the INT bit is set with an interrupt request from the A/D control status register enabled (ADCS:

INTE = 1), an interrupt request is generated. When the INT bit is cleared by the generated interrupt

processing, the pause of A/D conversion is cancelled.

●

A/D-converted data protection function when EI

OS used

•

The A/D conversion stops for data protection immediately before new data is overwritten to the A/D

data register while the EI

OS function is used to transfer the A/D conversion results from the A/D data

flag bit in the A/D control status register (ADCS: PAUS) is set to "1".

•

When the transfer of the A/D conversion results to memory by the EI

OS function is terminated, the

pause of A/D conversion is cancelled. If the A/D conversion is performed continuously, it is restarted. In

this case, the pause flag bit (ADCS:PAUS) is not cleared to "0" automatically. Clearing this bit writes 0

to it.

●

Processing flow of A/D conversion data protection function when EI

OS used

Figure 18.5-5 shows the processing flow of the A/D conversion data protection function when the EI

OS is

used.

Содержание F2MCTM-16LX











































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание F2MCTM-16LX

Отзывы:

Похожие инструкции для F2MCTM-16LX

Бренды по названию

Популярные бренды

Fujitsu F2MCTM-16LX, Руководство по оборудованию

Результаты поиска

Содержание F2MCTM-16LX

Отзывы:

Похожие инструкции для F2MCTM-16LX

Бренды по названию

Популярные бренды