Fuji Xerox DocuPrint CP225 w Скачать руководство пользователя страница 34

Страница: 34 / 187

Printer Connection and Software Installation



Connecting Printer to Your Computer

USB Connection

To connect the printer to a computer via USB:

Make sure that the printer is turned off and unplugged from the power source.

Connect the smaller USB connector into the USB port at the rear of the printer and the other end to a USB port
of the computer.

NOTE:

•

Do not connect the printer USB cable to the USB slot available on the keyboard.

Ethernet Connection

To connect the printer to a computer via Ethernet:

Make sure that the printer is turned off and all cables have been disconnected.

Connect one end of the Ethernet cable into the Ethernet port at the rear of the printer and the other end to an
Ethernet port of a router or hub.

NOTE:

•

Connect the Ethernet cable, only if you need to setup a wired connection. Connecting the Ethernet cable stops some features
or functions for Wireless network.

USB port

Ethernet port

Содержание DocuPrint CP225 w



























































































































































































Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CP225 w, Руководство пользователя

Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды