Fuji Xerox DocuPrint CP225 w Скачать руководство пользователя страница 117

Страница: 117 / 187

Using the Operator Panel Menus

117

• Panel Lock

Purpose:
To restrict access to the operator panel menus and change the password.

See also:

•

"Panel Lock Function" on page 124

Values:

This item is displayed when

Panel Lock Set

is set to

Enable

• Software Download

Purpose:
To enable or disable download of firmware updates.
Values:

• Show Network Info

Purpose:
To show or hide network information on the LCD panel.
Values:

USB Settings

Use the

USB Settings

menu to change printer settings affecting a USB port.

NOTE:

•

The value marked by an asterisk (*) is the factory default setting.

• Port Status

Purpose:
To change the USB settings on your printer.
Values:

Panel Lock Set

Disable

Does not restrict access to the operator panel menus.

Enable

Restricts access to the operator panel menus with a password.

Change Password

Change the password set to access the operator panel menus.

Enable

Enables firmware updates.

Disable

Disables firmware updates.

IP Address

Shows the IP address of the printer.

Host Name

Shows the host name of the printer.

Hide Information

Does not show network information.

Enable

Enables the USB interface.

Disable

Disables the USB interface.

Содержание DocuPrint CP225 w



























































































































































































Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CP225 w, Руководство пользователя

Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды