Fuji Xerox DocuPrint CP225 w Скачать руководство пользователя страница 137

Страница: 137 / 187

Troubleshooting

137



Clearing Paper Jams From the Center Output Tray

IMPORTANT:

•

To prevent electric shock, always turn off the printer and disconnect the power cord from the grounded outlet before
performing maintenance.

•

To avoid burns, do not clear paper jams immediately after printing. The fusing unit becomes extremely hot during use.

NOTE:

•

To resolve the error displayed on the LCD panel, you must clear all print media from the print media path.

Push the rear cover handle and open the rear cover.

Lift up the levers.

Remove any paper jammed from the rear of the printer by carefully pulling it in the direction of the arrow shown
in the following illustration.

Содержание DocuPrint CP225 w



























































































































































































Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CP225 w, Руководство пользователя

Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды