Fuji Xerox DocuPrint CP225 w Скачать руководство пользователя страница 148

Страница: 148 / 187

148

Troubleshooting



Auger Mark

NOTE:

•

If the problem continues even though you have taken suggested actions described above, contact the Fuji Xerox local
representative office or an authorized dealer.

Problem

Action

The printed result has auger mark.

The toner cartridges may be low or need to be replaced. Confirm the amount of
toner in each toner cartridge.

Check the toner level in the

Status

tab in the

Printer Status

window of the

SimpleMonitor.

Replace the toner cartridges as necessary.

Start

Clean Developer

Launch the Printer Setting Utility, and click

Clean Developer

on the

Diagnosis

tab.

Click

Start

Содержание DocuPrint CP225 w



























































































































































































Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды

Fuji Xerox DocuPrint CP225 w, Руководство пользователя

Результаты поиска

Содержание DocuPrint CP225 w

Отзывы:

Бренды по названию

Популярные бренды