Fuji Electric FVR-C11S-7EN Series Скачать руководство пользователя страница 7

Страница: 7 / 104

Safety Instructions

FVR-C11S-EN

Instructions on use

Instructions on transport/installation

WARNING

1. This inverter is designed to drive a three-

phase induction motor and is not usable for
a single-phase motor or any other pur-
poses.

There is a risk of fire.

2. This inverter may not be used as is for an

elevator, life-support system, or other pur-
pose directly affecting the safety of hu-
mans.
Safety precautions should be established
and practiced in terms of the entire system,
rather than the independent device.

Otherwise, an accident could occur.

WARNING

1. Attach the device to an incombustible ma-

terial such as metal.

Otherwise fire could occur.

2. Do not place the device near inflammables.

Otherwise fire could occur.

CAUTION

1. Do not carry the device by holding just the

surface cover.

Inverter may be dropped causing injury.

2. Do not allow foreign matter such as lint, pa-

per dust, small chips of wood or metal, and
dust to enter the inverter or adhere to the
heat sink.

Otherwise, a disaster such as burning
could occur.

3. Do not install or operate damaged inverter

or an inverter with a missing part.

Otherwise injury could occur.

4. Do not step on the product.

Otherwise injury could occur.

5. When stacking up in tiers, do not exceed

the number of tiers indicated on the pack-
ing carton.

Otherwise injury could occur.

Содержание FVR-C11S-7EN Series









































































































Результаты поиска

Содержание FVR-C11S-7EN Series

Отзывы:

Бренды по названию

Популярные бренды

Fuji Electric FVR-C11S-7EN Series, Инструкция по эксплуатации

Результаты поиска

Содержание FVR-C11S-7EN Series

Отзывы:

Бренды по названию

Популярные бренды