Freescale Semiconductor MC9S12ZVHL32 Скачать руководство пользователя страница 531 | Manualshive

Страница: 531 / 874

background image

Chapter 13 Serial Peripheral Interface (S12SPIV5)

S12ZVHY/S12ZVHL Family Reference Manual Rev. 1.05

Freescale Semiconductor

531

The CPOL clock polarity control bit specifies an active high or low clock and has no significant effect on
the transmission format.

The CPHA clock phase control bit selects one of two fundamentally different transmission formats.

Clock phase and polarity should be identical for the master SPI device and the communicating slave
device. In some cases, the phase and polarity are changed between transmissions to allow a master device
to communicate with peripheral slaves having different requirements.

13.4.3.2

CPHA = 0 Transfer Format

The first edge on the SCK line is used to clock the first data bit of the slave into the master and the first
data bit of the master into the slave. In some peripherals, the first bit of the slave’s data is available at the
slave’s data out pin as soon as the slave is selected. In this format, the first SCK edge is issued a half cycle
after SS has become low.

A half SCK cycle later, the second edge appears on the SCK line. When this second edge occurs, the value
previously latched from the serial data input pin is shifted into the LSB or MSB of the shift register,
depending on LSBFE bit.

After this second edge, the next bit of the SPI master data is transmitted out of the serial data output pin of
the master to the serial input pin on the slave. This process continues for a total of 16 edges on the SCK
line, with data being latched on odd numbered edges and shifted on even numbered edges.

Data reception is double buffered. Data is shifted serially into the SPI shift register during the transfer and
is transferred to the parallel SPI data register after the last bit is shifted in.

After 2n

1

(last) SCK edges:

•

Data that was previously in the master SPI data register should now be in the slave data register
and the data that was in the slave data register should be in the master.

•

The SPIF flag in the SPI status register is set, indicating that the transfer is complete.

is a timing diagram of an SPI transfer where CPHA = 0. SCK waveforms are shown for

CPOL = 0 and CPOL = 1. The diagram may be interpreted as a master or slave timing diagram because
the SCK, MISO, and MOSI pins are connected directly between the master and the slave. The MISO signal
is the output from the slave and the MOSI signal is the output from the master. The SS pin of the master
must be either high or reconfigured as a general-purpose output not affecting the SPI.

1. n depends on the selected transfer width, please refer to

Section 13.3.2.2, “SPI Control Register 2 (SPICR2)

«
...
529
530
531
532
533
...
»

Содержание MC9S12ZVHL32











































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MC9S12ZVHL32

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: IBM Страницы: 214

Optidrive Elevator

Бренд: Invertek Страницы: 5

Бренд: Techtrol Страницы: 4

Бренд: Kelly Страницы: 32

SWD Starter Kit

Бренд: ez-wheel Страницы: 30

Бренд: Technologic Страницы: 21

Бренд: CLS Страницы: 6

Бренд: Samson Страницы: 130

StreamMax Pump Controller

Бренд: Oase Страницы: 142

Бренд: DELTA DORE Страницы: 9

Бренд: Regin Страницы: 24

Бренд: YGE Страницы: 4

Бренд: Riso Страницы: 88

Бренд: WOBIT Страницы: 25

Бренд: Aventics Страницы: 24

MegaRAID SAS 9361-24i

Бренд: Broadcom Страницы: 6

Бренд: Regada Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды