manualshive.com logo in svg

FMC Technologies Proline Promass 83 E, Описание функций устройства

Поделиться
Скачать
FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 76

Issue/Rev. 0.2 (12/12)

Page 76

 • 

MN0M023

7 Block OUTPUTS

Device Functions Proline Promass 83 

START VALUE 
FREQUENCY
(4202)

!

Note!

This function is not available unless the FREQUENCY setting was selected in the 
OPERATION MODE function (4200).

Use this function to define an initial frequency for the frequency output. You define the 
associated measured value of the measuring range in the VALUE F LOW function (4204) 
described on page 77.

User input:

5-digit fixed-point number: 0...10000 Hz

Factory setting:

0 Hz

Example:
• VALUE F LOW = 0 kg/h, initial frequency = 0 Hz: 

i.e. a frequency of 0 Hz is output at a flow of 0 kg/h.

• VALUE F LOW = 1 kg/h, initial frequency = 10 Hz: 

i.e. a frequency of 10 Hz is output at a flow of 1 kg/h.

END VALUE 
FREQUENCY
(4203)

!

Note!

This function is not available unless the FREQUENCY setting was selected in the 
OPERATION MODE function (4200).

Use this function to define a full scale frequency for the frequency output. You define the 
associated measured value of the measuring range in the VALUE F HIGH function (4205) 
described on page 77.

User input:

5-digit fixed-point number 2...10000 Hz

Factory setting:

10000 Hz

Example:
• VALUE F HIGH = 10000 kg/h, full scale frequency = 10000 Hz: 

i.e. a frequency of 10000 Hz is output at a flow of 10000 kg/h.

• VALUE F HIGH = 3600 kg/h, full scale frequency = 10000 Hz: 

i.e. a frequency of 10000 Hz is output at a flow of 3600 kg/h.

!

Note!

In the FREQUENCY operating mode the output signal is symmetrical 
(on/off ratio = 1:1). At low frequencies the pulse duration is limited to a 
maximum of 2 seconds, i.e. the on/off ratio is no longer symmetrical.

Function description

OUTPUTS 

o

 PULSE/FREQUENCY OUTPUT (1...2) 

o

 CONFIGURATION (FREQUENCY)

Содержание Proline Promass 83 E















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды