manualshive.com logo in svg

FMC Technologies Proline Promass 83 E, Описание функций устройства

Поделиться
Скачать
FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 183

Issue/Rev. 0.2 (12/12)

MN0M023 • Page 183

Device Functions Proline Promass 83 

11 Block SUPERVISION

11.1.2

Function group OPERATION

SUPERVISION

J

Ÿ

SYSTEM

JAA

Ÿ

CONFIGURATION

800

 

OPERATION

804

Function description

SUPERVISION 

o

 SYSTEM 

o

 OPERATION

ACTUAL SYSTEM 
CONDITION
(8040) 

Use this function to check the present system condition.

Display:

“SYSTEM OK” or the fault / notice message with the highest priority.

PREVIOUS SYSTEM 
CONDITION
(8041) 

Use this function to view the fifteen most recent fault and notice messages since 
measuring last started.

Display:

The 15 most recent fault or notice messages.

SIMULATION FAILSAFE 
MODE
(8042)

Use this function to set all inputs, outputs and totalizers to their defined failsafe modes, in 
order to check whether they respond correctly. During this time, the message 
“SIMULATION FAILSAFE MODE” appears on the display.

Options:

ON
OFF

Factory setting:

OFF

SIMULATION 
MEASURAND
(8043)

Use this function to set all inputs, outputs and totalizers to their defined flow-response 
modes, in order to check whether they respond correctly. During this time, the message 
“SIMULATION MEASURAND” appears on the display.

Options:

OFF
MASS FLOW 
VOLUME FLOW
CORRECTED VOLUME FLOW
DENSITY
REFERENCE DENSITY
TEMPERATURE

Factory setting:

OFF

"

Caution!

• The measuring device cannot be used for measuring while this simulation is in 

progress.

• The setting is not saved if the power supply fails.

Содержание Proline Promass 83 E















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды