FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 117

Страница: 117 / 206

Issue/Rev. 0.2 (12/12)

MN0M023 • Page 117

Device Functions Proline Promass 83

8 Block INPUTS

8.2.2

Function group OPERATION

INPUTS

STATUS INPUT

FAA

CURRENT INPUT

FCA

CONFIGURATION

520

OPERATION

524

Function description

INPUTS

CURRENT INPUT

OPERATION

ACTUAL CURRENT
INPUT
(5240)

The actual value of the input current appears on the display.

Display:

0.0...25 mA

SIMULATION
CURRENT INPUT
(5241)

Use this function to activate simulation of the current output.

Options:

OFF
ON

Factory setting:

OFF

Note!

• An active simulation is indicated by the

“SIM. CURRENT 1” (# 661) notice message.

• The value output for the simulation at the current input is defined in the function

VALUE SIMULATION CURRENT INPUT (5242).

• The measuring device remains fully operational during the simulation and the current

measured values are output correctly via the other outputs and the display.

Caution!

The setting is not saved if the power supply fails.

VALUE SIMULATION
CURRENT INPUT
(5242)

Note!

This function is only available if the function SIMULATION
CURRENT INPUT (5241) is switched on.

Use this function to specify a freely selectable value, e.g. 12 mA, which is to be simulated
at the current input. This value is used to test downstream devices and the measuring
device itself.

User input:

0.00...25.00 mA

Factory setting:

0.00 mA or 4 mA (depending on the setting in function 5201).

Caution!

The setting is not saved if the power supply fails.

Содержание Proline Promass 83 E















































































































































































































Результаты поиска

Содержание Proline Promass 83 E

Отзывы:

Бренды по названию

Популярные бренды

FMC Technologies Proline Promass 83 E, Описание функций устройства

Результаты поиска

Содержание Proline Promass 83 E

Отзывы:

Бренды по названию

Популярные бренды