FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 206

FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 55

Issue/Rev. 0.2 (12/12)

MN0M023 • Page 55

Device Functions Proline Promass 83

5 Block USER INTERFACE

FORMAT
(2622)

!

Note!

This function is not available unless a number was selected in the ASSIGN function
(2620).

Use this function to define the maximum number of places after the decimal point for the
second value displayed in the information line.

Options:

XXXXX. - XXXX.X - XXX.XX - XX.XXX -X.XXXX

Factory setting:

X.XXXX

!

Note!

• Note that this setting only affects the reading as it appears on the display, it has no

influence on the accuracy of the system's calculations.

• The places after the decimal point as computed by the measuring device cannot always

be displayed, depending on this setting and the engineering unit. In such instances an
arrow appears on the display between the measuring value and the engineering unit
(e.g. 1.2

o

kg/h), indicating that the measuring system is computing with more

decimal places than can be shown on the display.

DISPLAY MODE
(2623)

!

Note!

This function is not available unless one of the following was selected in the ASSIGN
function (2620):
• MASS FLOW BARGRAPH IN %
• VOLUME FLOW BARGRAPH IN %
• CORRECTED VOLUME FLOW BARGRAPH IN %

Use this function to define the format of the bar graph.

Options:

STANDARD
Simple bar graph with 25 / 50 / 75% gradations and integrated sign.

A0001258

SYMMETRY
Symmetrical bar graph for positive and negative directions of flow, with
–50 / 0 / +50% gradations and integrated sign..

A0001259

Factory setting:

STANDARD

Function description

USER INTERFACE

o

INFORMATION LINE

o

MULTIPLEX

«
...
53
54
55
56
57
...
»

Содержание Proline Promass 83 E















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды