FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 17

Страница: 17 / 206

Issue/Rev. 0.2 (12/12)

MN0M023 • Page 17

Device Functions Proline Promass 83

3 Block MEASURED VARIABLES

3.2

Group SYSTEM UNITS

3.2.1

Function group CONFIGURATION

MEASURED

VARIABLES

MEASURING VALUES

AAA

SYSTEM UNITS

ACA

CONFIGURATION

040

Function description

MEASURED VARIABLES

SYSTEM UNITS

CONFIGURATION

You can select the units for measured variables in this function group.

UNIT MASS FLOW
(0400)

Use this function to select the unit for displaying the mass flow (mass/time).

The unit you select here is also valid for:
• Current outputs
• Frequency outputs
• Relay switch points (limit value for mass flow, flow direction)
• Low flow cut off

Options:

Metric:
gram

g/s; g/min; g/h; g/day

kilogram

kg/s; kg/min; kg/h; kg/day

ton

t/s; t/min; t/h; t/day

US:
ounce

oz/s; oz/min; oz/h; oz/day

pound

lb/s; lb/min; lb/h; lb/day

ton

ton/s; ton/min; ton/h; ton/day

For arbitrary units (see function TEXT ARBITRARY MASS on page 22)
_ _ _ _

_ _ _ _/s; _ _ _ _/min; _ _ _ _/h; _ _ _ _/day

Factory setting:

Country-dependent (kg/h or US-lb/min)

Note!

If you defined a unit of mass in the ARBITRARY UNIT 060 function group (see page 22)
the unit in question is shown here.

UNIT MASS
(0401)

Use this function to select the unit for displaying the mass.

The unit you select here is also valid for:
• Pulse value (e.g. kg/p)

Options:

Metric

g; kg; t

oz; lb; ton

For free selectable units

_ _ _ _ (see function TEXT ARBITRARY MASS on page 22)

Factory setting:

Country-dependent (kg or US-lb)

Note!

• If you defined a unit of mass in the ARBITRARY UNIT 060 function group

(see page 22) the unit in question is shown here.

• The unit of the totalizers is independent of your choice here. The unit for each

totalizer is selected separately for the totalizer in question.

Содержание Proline Promass 83 E















































































































































































































Результаты поиска

Содержание Proline Promass 83 E

Отзывы:

Бренды по названию

Популярные бренды

FMC Technologies Proline Promass 83 E, Описание функций устройства

Результаты поиска

Содержание Proline Promass 83 E

Отзывы:

Бренды по названию

Популярные бренды