FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 129

Страница: 129 / 206

Issue/Rev. 0.2 (12/12)

MN0M023 • Page 129

Device Functions Proline Promass 83

9 Block BASIC FUNCTION

9.2.4

Function group ADJUSTMENT

BASIC FUNCTION

HART

GAA

PROCESS PARAMETER

GIA

CONFIGURATION

640

EPD PARAMETER

642

REFERENCE PARAMETER 646

ADJUSTMENT

648

Function description

BASIC FUNCTION

PROCESS PARAMETER

ADJUSTMENT

ZEROPOINT
ADJUSTMENT
(6480)

This function enables a zero point adjustment to be automatically carried out. The new
zero point determined by the measuring system is adopted by the function ZEROPOINT
(see page 135).

Options:

CANCEL
START

Factory setting:

CANCEL

Caution!

Before carrying this out, please refer to the Operating Instructions

Proline Promass 83

BA 059D/06/en for a detailed description of the procedure for zero point adjustment.

Note!

• Programming is locked during zero point adjustment.

The message“ZERO ADJUST RUNNING” appears on the display.

• If the zero point adjustment is not possible (e.g. if v > 0.1 m/s) or has been canceled,

the alarm message “ZERO ADJUST NOT POSSIBLE” appears on the display.

• If the Promass 83 measuring electronics are fitted with a status input, then the zero

point can also be activated by using this input.

Содержание Proline Promass 83 E















































































































































































































Результаты поиска

Содержание Proline Promass 83 E

Отзывы:

Бренды по названию

Популярные бренды

FMC Technologies Proline Promass 83 E, Описание функций устройства

Результаты поиска

Содержание Proline Promass 83 E

Отзывы:

Бренды по названию

Популярные бренды