manualshive.com logo in svg

FMC Technologies Proline Promass 83 E, Описание функций устройства

Поделиться
Скачать
FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 144

Issue/Rev. 0.2 (12/12)

Page 144

 • 

MN0M023

10 Block SPECIAL FUNCTION

Device Functions Proline Promass 83 

REFERENCE 
TEMPERATURE
(7009)

!

Note!

This function is only available if OFF, °BRIX or FLEXIBLE was 

not

 selected in the 

function DENSITY FUNCTION (7000).

Use this function to enter the reference temperature for the density functions and for 
calculating the corrected volume flow and the corrected volume.

User input:

4-digit fixed-point number, including unit and sign

Factory setting:

20 °C

MODE
(7021)

!

Note!

This function is not available unless the FLEXIBLE setting was selected in the DENSITY 
FUNCTION function (7000).

Use this function to select a user-specific method of calculating the concentration of the 
density and temperature measured.

In order to use this function, the following values are required:
• Concentration (see formula)
• Currently measured density
• Currently measured temperature

The concentration is calculated from the density and temperature as follows:
K = A0 + A1 · 

U

 + A2 · 

U

2

 + A3 · 

U

3

 + A4 · 

U

4

 + B1 · T + B2 · T

2

 + B3 · T

3

K = Concentration

U

= currently measured density

A0 = Value from function COEFFICIENT A0 (7032)
A1 = Value from function COEFFICIENT A1 (7033) 
A2 = Value from function COEFFICIENT A2 (7034) 
A3 = Value from function COEFFICIENT A3 (7035) 
A4 = Value from function COEFFICIENT A4 (7036) 
B1 = Value from function COEFFICIENT B1 (7037) 
B2 = Value from function COEFFICIENT B2 (7038)
B3 = Value from function COEFFICIENT B3 (7039)
T = currently measured temperature in °C

Options:

% MASS 3D
% VOLUME 3D
% MASS 2D
% VOLUME 2D
OTHERS 3D
OTHERS 2D

Factory setting:

% MASS 3D

!

Note!

If the relation between concentration density and temperature is given as table, the 
equation coefficients can be determined by Hauser e.g. via a coefficient 
calculation program and transmitted to the measuring device.

Function description

SPECIAL FUNCTION 

o

 DENSITY FUNCTIONS 

o

 CONFIGURATION

Содержание Proline Promass 83 E















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды