manualshive.com logo in svg

FMC Technologies Proline Promass 83 E, Описание функций устройства

Поделиться
Скачать
FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 75

Issue/Rev. 0.2 (12/12)

MN0M023 • Page 75

Device Functions Proline Promass 83 

7 Block OUTPUTS

Function description

OUTPUTS 

o

 PULSE/FREQUENCY OUTPUT (1...2) 

o

 CONFIGURATION (FREQUENCY)

ASSIGN FREQUENCY
(4201)

!

Note!

This function is not available unless the FREQUENCY setting was selected in the 
OPERATION MODE function (4200).

Use this function to assign a measured variable to the frequency output.

Options:

OFF
MASS FLOW
VOLUME FLOW
CORRECTED VOLUME FLOW
DENSITY
REFERENCE DENSITY
TEMPERATURE

Advanced options with optional software package CONCENTRATION:

TARGET MASS FLOW
% TARGET MASS FLOW
TARGET VOLUME FLOW
% TARGET VOLUME FLOW
CORRECTED TARGET VOLUME FLOW
CARRIER MASS FLOW
% CARRIER MASS FLOW
CARRIER VOLUME FLOW
% CARRIER VOLUME FLOW
CORRECTED CARRIER VOLUME FLOW
% BLACK LIQUOR
°BAUME
°API
°PLATO
°BALLING
°BRIX
OTHERS (_ _ _ _ flexible concentration)

Advanced options with optional software package ADVANCED DIAGNOSIS:

MASS FLOW DEVIATION
DENSITY DEVIATION
REFERENCE DENSITY DEVIATION
TEMPERATURE DEVIATION
TUBE DAMPING DEVIATION
ELECTRODYNAMIC SENSOR DEVIATION
OPERATING FREQUENCY FLUCTUATION DEVIATION
TUBE DAMPING FLUCTUATION DEVIATION

Factory setting:

MASS FLOW

!

Note!

If you select OFF, the only function shown in the CONFIGURATION function group is 
this function, in other words ASSIGN FREQUENCY (4201).

Содержание Proline Promass 83 E















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды