manualshive.com logo in svg

FMC Technologies Proline Promass 83 E, Описание функций устройства

Поделиться
Скачать
FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 162

Issue/Rev. 0.2 (12/12)

Page 162

 • 

MN0M023

10 Block SPECIAL FUNCTION

Device Functions Proline Promass 83 

10.2.5

Function group OPERATION

SPECIAL FUNCTION

H

Ÿ

BATCHING FUNCTION

HCA

Ÿ

CONFIGURATION

720

 

VALVE PARAMETER

722

 

SUPERVISION

724

 

OPERATION

726

Function description

SPECIAL FUNCTION 

o

 BATCHING FUNCTION 

o

 OPERATION

BATCH PROCEDURE
(7260)

Use this function to control a batching process. The batching can be started manually or a 
batching already running can be interrupted or stopped at any time.

Options:

STOP (Stop batching)
START (Start batching)
HOLD (Interrupt batching)
GO ON (Continue batching)

Factory setting:

STOP

!

Note!

• This function can also be controlled via the status input, (see function ASSIGN 

STATUS INPUT (5000) on page 112).

• If the information line has been assigned to BATCHING MENU (see page 50), the 

application-specific functions of the minus key (START-STOP) and the plus key 
(HOLD-GO ON / batching specification) are defined locally. In this way, a direct 
batching control station is available locally at the measuring device by means of the 
user interface (not access-protected).

• In the event of a fault:

– during the batching process, the batching is canceled (STOP) and the local display 

alternates between displaying the batching menu and the fault message.

• If the positive zero return is activated, (see page 133):

– during the batching process, the batching is canceled (STOP).
– during a pause in the batching (option HOLD), the batching cannot be restarted, 

(see also notice messages # 571 and # 572 in the Operating Instructions 

Proline 

Promass 83

, BA 059D/06/en, Chapter Troubleshooting.

BATCH UPWARDS
(7261)

In this function the batching progress can be read upwards, i.e. 

starting at 0 

the quantity 

displayed increases until the batching process is complete.

Display:

Floating-point number incl. unit

!

Note!

The value of this function can be output via the current output.

Содержание Proline Promass 83 E















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды