manualshive.com logo in svg

FMC Technologies Proline Promass 83 E, Описание функций устройства

Поделиться
Скачать
FMC Technologies Proline Promass 83 E Скачать руководство пользователя страница 42

Issue/Rev. 0.2 (12/12)

Page 42

 • 

MN0M023

5 Block USER INTERFACE

Device Functions Proline Promass 83 

5.2.2

Function group MULTIPLEX

USER INTERFACE

C

Ÿ

CONTROL

CAA

 

MAIN LINE

CCA

Ÿ

CONFIGURATION

220

 

MULTIPLEX

222

Function description

USER INTERFACE 

o

 MAIN LINE 

o

 MULTIPLEX

ASSIGN
(2220)

Use this function to define the second reading to be displayed in the main line alternately 
(every 10 seconds) with the value defined in the ASSIGN function (2200).

Options (standard):

OFF
MASS FLOW
MASS FLOW IN %
VOLUME FLOW
VOLUME FLOW IN %
CORRECTED VOLUME FLOW
CORRECTED VOLUME FLOW IN %
DENSITY
REFERENCE DENSITY
TEMPERATURE
ACTUAL CURRENT (1...3)
ACTUAL FREQUENCY (1...2)
TOTALIZER (1...3)
ACTUAL CURRENT INPUT

Factory setting:

OFF

Advanced options with optional software package BATCHING:

BATCH NAME (“BATCH # 1” or “BEER 330”, etc.)
BATCH QUANTITY (overall quantity to be batched)
BATCH COUNTER (batching processes carried out)
BATCH SUM (effective total batching quantity)

!

Note!

The options given in the BATCHING software package always refer to the batching 
selected (“BATCH # 1”, “BATCH # 2”, etc.) in the BATCH SELECTOR function 
(page 147). Example: If BATCH # 1 was selected in the BATCH SELECTOR function 
(7200), then only the values from BATCH # 1 (batch name, batch quantity etc.) can be 
displayed.

Advanced options with optional software package CONCENTRATION:

TARGET MASS FLOW
% TARGET MASS FLOW
TARGET VOLUME FLOW
% TARGET VOLUME FLOW
CORRECTED TARGET VOLUME FLOW
CARRIER MASS FLOW
% CARRIER MASS FLOW
CARRIER VOLUME FLOW
% CARRIER VOLUME FLOW
CORRECTED CARRIER VOLUME FLOW
% BLACK LIQUOR
°BAUME
°API
°PLATO
°BALLING
°BRIX
OTHERS (_ _ _ _ flexible concentration)

(continued on next page)

Содержание Proline Promass 83 E















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды