FLIGHT DESIGN CTLS Series Скачать руководство пользователя | Manualshive

Страница: 106 / 176

background image

Maintenance and Inspection Procedures Manual

Type:

CT

Series:

CTLS

LSA

Page: 4-69

AF 04800001

Revision No. 3

Date: 14 Sep 2008

Fig. 10

To reduce tension:

1. Look the way the threaded adjuster bushing is secured by the safety wire. Remove the safety

wire.

2. Release the tips (Fig. 10, item 2), having loosened the locking nut (Fig. 10, item 3) by a 10x13

wrench.

3. Take care that the tips are inserted into the threaded adjuster bushing body at least

64

15

inch / 6

mm.

4.  Unscrew the tips half-turn on each threaded adjuster bushing.
5.  Check rudder cables tension (11.75 ± 0.25 kgf).
6.  Repeat items 4-5, if necessary.
7.  Tighten the nuts (Fig. 10, item 3) by a 10x13 wrench unscrewing them from the tip towards the

threaded adjuster bushing.

8. Lock the threaded adjuster bushing by safety wire.

To increase cables tension, perform items 1 through 8, having reversed tip rotation for the operation 4.

4.3.3.5 Verification of Rudder Installation and Adjustment

1. Set the nose wheel along the longitudinal axle of the plane.

a.  Make sure the right and left pedals are on the same line.
b.  The rudder must be in neutral position, along the plane axle.
c.  The aircraft must run straight on a plane surface

2. verify deflection angles following chapter 4.3.3.6.1
3. Lift up the front of the plane so that the nose wheel is off the ground. Deflect the rudder by the

pedals to the left. Release the pedals and the rudder and nose wheel must return to the neutral
position by the returning mechanism. Check the same for the right deflection. Note that
unsatisfactory functioning of the returning mechanism may be the result of excessive tension of
the rudder control cables.

«
...
104
105
106
107
108
...
»

Содержание CTLS Series

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CTLS Series

Бренд: AEROPRAKT Страницы: 53

Robin DR400-140

Бренд: Aerosoft Страницы: 35

DIAMONDcross 125 HG

Бренд: CHARLY Страницы: 40

Бренд: Cessna Страницы: 42

Бренд: Hacker Страницы: 23

Бренд: Nova Страницы: 41

Бренд: Team 5 Страницы: 100

Бренд: Crivit Страницы: 12

Бренд: FlyPurrz Страницы: 2

Бренд: Badfish Страницы: 9

Бренд: WAY Gliders Страницы: 25

Бренд: MAC PARA Страницы: 40

Бренд: Gradient Страницы: 16

Бренд: THRUSH Страницы: 86

Super-Cub PA-18-150

Бренд: Piper Страницы: 56

Бренд: Piper Страницы: 408

Бренд: JMB Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды