Extreme Networks ExtremeWare 7.5 Скачать руководство пользователя страница 761 | Manualshive

Страница: 761 / 2546

background image

enable sys-health-check

ExtremeWare 7.5 Command Reference Guide

761

enable sys-health-check

enable sys-health-check

Description

Enables the BlackDiamond system health checker.

NOTE

This command is available only on the BlackDiamond switches.

Syntax Description

This command has no arguments or variables.

Default

Enabled

Usage Guidelines

The system health checker tests I/O modules, MSM modules, and the backplane by forwarding packets
every 4 seconds. Additional checking for the validity of these packets is completed by performing a
checksum.

By isolating faults to a specific module, MSM, or backplane connection, the system health checker
prevents corrupted packets from being propagated to the CPU, upper layer modules, or the rest of your
network. If you observe a failure, please contact Extreme Technical Support.

Depending on how you have configured the system health checker, failed system health checks may
generate critical error messages in the syslog, and may also send a trap and/or shut down the system.
The system health checker will continue to periodically forward test packets to failed components. If
auto-recovery is configured, the system will attempt to automatically reset the faulty module and bring
it back online.

In ExtremeWare versions prior to 6.2, you cannot use both mirroring and the system health checker at
the same time. If you configure mirroring with the system health checker enabled, the health checker
will indicate that it has been disabled by sending a message to the syslog. In version 6.2 or later, this
restriction does not apply.

To configure the health checker, use the following command:

configure sys-health-check [alarm-level [card-down | default | log | system-down |

traps] | auto-recovery <number of tries>]

The alarm-level and auto-recovery options are mutually exclusive; configuring an alarm-level disables
auto-recovery, and configuring auto-recovery overrides the alarm-level setting.

Example

The following command enables the BlackDiamond system health checker:

enable sys-health-check

«
...
759
760
761
762
763
...
»

Содержание ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeWare 7.5

Бренд: Valcom Страницы: 5

850DP - Phaser Color Solid Ink Printer

Бренд: Xerox Страницы: 2

AUTOMATED MESSAGE DELIVERY SYSTEM 5.0

Бренд: Alcatel-Lucent Страницы: 4

38000827 - Macromedia ColdFusion MX Standard Edition

Бренд: Adobe Страницы: 68

FLEX - DEVELOPING COMPONENTS AND THEMES

Бренд: MACROMEDIA Страницы: 82

DISK DIRECTOR SUITE 10

Бренд: ACRONIS Страницы: 127

Бренд: M-Audio Страницы: 4

Бренд: Allied Telesis Страницы: 46

Бренд: Sharp Страницы: 12

NAPCKE-AB-AA - VirusScan For NetApp

Бренд: McAfee Страницы: 54

ASSET MANAGEMENT SUITE 7.0

Бренд: Symantec Страницы: 4

ANTIVIRUS 5.2 - FOR NETWORK ATTACHED STORAGE

Бренд: Symantec Страницы: 3

Altiris CMDB Solution 7.0

Бренд: Symantec Страницы: 64

Navigation app for iPhone/iPad

Бренд: TomTom Страницы: 84

Бренд: Fermax Страницы: 8

COLDFUSION STUDIO 5-USING COLDFUSION 5...

Бренд: MACROMEDIA Страницы: 328

FLASH 8-USING FLASH

Бренд: MACROMEDIA Страницы: 678

DocuPrint 100MX

Бренд: Xerox Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды