Evoqua DEPOLOX POOL COMPACT WALLACE & TIERNAN Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 88

background image

DEPOLOX® Pool Compact

5. Installation

35

EN

5.

Installation

5.1

Scope of delivery

The scope of delivery includes the following,
depending on the version selected:

•

Electronics module (module name E02)
with sensor cable pre-wired

•

Flow cell, pressurized version (module
name D02)

•

LED glow stick (pre-wired)

•

Sensors:
•

Chlorine sensor (free chlorine)

•

pH sensor

•

ORP (Redox) sensor

•

Multi-sensor

•

4-way mA output card (depending on
selected version)

•

Top-hat rail

•

Assembly accessories

•

Instruction manual

5.2

Transport and storage

Transport

The DEPOLOX® Pool Compact Measuring,
Control and Dosing System is shipped in stan-
dard packaging. During transport, the packa-
ged DEPOLOX® Pool Compact must be
handled carefully and should not be exposed
to wet weather or moisture.
Check that the transport packaging is unda-
maged. In the event of damage, please inform
the transport company immediately, as your
rights to compensation will otherwise be lost.
If a component is damaged, please contact
your affiliate immediately.
Keep the packaging until the system has been
commissioned and put into operation.

Storage

Electronics module, flow cell and sensors must
be stored in dry condition without any residual
water in a dry place that is not exposed to the
elements.

Shut-down

The DEPOLOX® Pool Compact may only be
taken out of operation by trained and authori-
zed personnel.

5.3

Required ambient conditions

•

The DEPOLOX® Pool Compact must be
protected against moisture, rain, frost,
heat and direct sunlight and may there-
fore not be installed outdoors.

•

Do not use the DEPOLOX® Pool Compact
in environments where there are flamma-
ble gases, fumes or dust or conductive
dust.

•

Do not subject the DEPOLOX® Pool Com-
pact to strong shocks or vibrations.

•

The air in the room must be non-conden-
sing.

5.4

Mechanical Installation

NOTICE

Correct and safe operation can only be gua-
ranteed if the requirements for the ambient
conditions are met. All applicable national
and local regulations must be observed!

WARNING

Risk of injury or damage to the installation!

•

Only authorized and qualified electrici-
ans are permitted to install the DEPO-
LOX® Pool Compact.

•

All electrical work on the DEPOLOX®
Pool Compact must be carried out by
authorized and qualified electricians.

•

Modifications to the device other than
those described in this instruction
manual are not permissible.

NOTICE

•

Install the flow cell to the left of the
electronics module.

•

Leave a clearance of at least 250 mm
above the flow cell for working with the
sensors.

•

Screws and dowels for fixing to a solid
wall are included in the scope of delivery.

•

Tallow-drop screws and dowels for fixing
to a solid wall are included in the scope
of delivery.

•

If the device is to be installed on a suita-
ble lightweight wall, use the appropriate
mounting fixtures. Not included in the
scope of delivery!

«
...
33
34
35
36
37
...
»

Содержание DEPOLOX POOL COMPACT WALLACE & TIERNAN

























































































Отзывы:

Нет отзывов

Похожие инструкции для DEPOLOX POOL COMPACT WALLACE & TIERNAN

Бренд: Bacharach Страницы: 64

Бренд: E Instruments Страницы: 2

Бренд: M & I Instruments Страницы: 2

Бренд: Keysight Страницы: 66

Бренд: JENCO Страницы: 13

Бренд: Power Measurement Страницы: 20

Бренд: Water I.D. Страницы: 56

Бренд: Meec tools Страницы: 23

NetSure M832DNA

Бренд: Vertiv Страницы: 176

Бренд: Liquid Controls Страницы: 16

Бренд: Omega Страницы: 4

Бренд: Racelogic Страницы: 15

Бренд: wtw Страницы: 72

Бренд: Fluke Страницы: 5

Бренд: PCE Health and Fitness Страницы: 4

Бренд: X-Rite Страницы: 21

Бренд: DeNovix Страницы: 93

Бренд: Sonel Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды