background image

52

   

4. WARRANTY COVERAGE PERIOD

This limited warranty will be in effect from the date of delivery to the first retail consumer or the date the

Product is first put to use, whichever occurs first, for a period of TWELVE (12) CONSECUTIVE MONTHS. 
Except that exhaust emission-related components are warranted for sixty (60) consecutive months or one

hundred seventy five (175) hours of engine use, whichever occurs first; and evaporative emission related

components are warranted for twenty-four (24) consecutive months. 

Please see your Authorized Evinrude

Outboard Engine Dealer for emission-related service.

The repair or replacement of parts or the performance of service to Product under this warranty does not

extend the life of this limited warranty beyond its original expiration date. All 

Evinrude/Johnson

® 

Genuine

Parts

 and accessories installed by an authorized dealer at the time of sale bear the standard BRP parts

and accessories one-year limited warranty. 

5. CONDITIONS TO HAVE WARRANTY COVERAGE

This warranty coverage is available only on 

Evinrude

 Multi Fuel Engines purchased as new and unused

from a dealer authorized to distribute 

Evinrude

 products in the country in which the sale occurred (“Deal-

er”), and then only after the BRP specified pre-delivery inspection process has been completed and doc-

umented by the purchaser and Dealer. Warranty coverage only becomes available upon proper

registration of Product by Dealer or owner.
Only the original purchaser and any subsequent owners who reside in the United States and Canada and

have purchased Product from BRP or an authorized U.S. or Canadian Dealer are eligible for warranty reg-

istration and warranty coverage hereunder. Such limitations are necessary in order to allow BRP to protect

the safety of its products, its consumers, and the general public.
As outlined in the Operator’s Guide, timely routine required maintenance must be performed to maintain

warranty coverage. BRP may require proof of proper maintenance prior to authorizing warranty coverage.

6. WHAT TO DO TO OBTAIN WARRANTY COVERAGE

The registered owner must notify an authorized Dealer within two (2) days of the appearance of a defect.

The potentially defective Product must not be used until it has been inspected by an Authorized Service

Point. BRP is not responsible for damages caused by the use of a Product after the appearance of a de-

fect. Owner must bring Product, including any defective part therein, to Dealer promptly after the appear-

ance of the defect, and in any event, within the warranty period, and must provide Dealer with reasonable

opportunity to repair the defect. The expenses of transporting Product to and from Dealer for warranty ser-

vice are to be borne by the owner.
If the Product has not previously been registered, the owner may also be required to present proof of pur-

chase to Dealer for warranty repairs. Owner is required to sign the repair/work order prior to the start of

the repair in order to validate the warranty repair.
All parts replaced under this warranty become the property of BRP.

7. WHAT BRP WILL DO

BRP’s obligations under this warranty are limited to, at its sole discretion, repairing or replacing parts of

Product found to be defective in material or workmanship, in the reasonable judgment of BRP. Such repair

or replacement of parts will be done without charge for parts and labor, at any authorized Dealer. BRP’s

responsibility is limited to making the required repairs or replacements of parts with new or BRP-certified

re-manufactured parts. No claim of breach of warranty shall be cause for cancellation or rescission of the

sale of Product to owner.
In the event that warranty service is required outside of the fifty United States or Canada, owner will bear

responsibility for any additional charges due to local practices and conditions, such as, but not limited to,

freight, insurance, taxes, license fees, import duties, and any and all other financial charges, including

those levied by governments, states, territories and their respective agencies.
BRP reserves the right to improve, modify or change Products from time to time without assuming any

obligation to modify Products previously manufactured.

8. TRANSFER

If the ownership of Product is transferred during the warranty coverage period, this warranty shall be trans-

ferred and be valid for the remaining coverage period provided that the former or new owner promptly con-

tacts BRP or Dealer and gives the name and address of the new owner.

9. CONSUMER ASSISTANCE

In the event of a controversy or dispute in connection with this BRP limited warranty, BRP recommends

that you first try to resolve the issue at the dealership level by discussing the issue with Dealer’s service

manager or owner;
If further assistance is required, please contact BRP US Inc. / Outboard Engines Division, After Sales Sup-

port, P.O Box 597, Sturtevant, WI 53177, 1-262-884-5993.

* In Canada, products are distributed and serviced by Bombardier Recreational Products Inc.

® Registered trademark of Bombardier Recreational Products Inc. or its affiliates.

© 2012 BRP US Inc. All rights reserved. Limited Warranty MFE - September 2012

Содержание 30 HORSEPOWER MFE





























































Отзывы: