Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 24

Страница: 24 / 60

Using The Evinrude MFE Outboard

TILTING AND TRIM

TILT UP

Move the tilt/run lever to TILT position.

Grasp the tilt grip on engine cover and tilt out-

board to the full tilt position.

IMPORTANT:

Use the tilt grip to tilt your out-

board. Do not use the tiller handle as a lever.

The tilt support bracket will automatically en-

gage.

TILT DOWN

Move tilt/run lever to RUN position.

Grasp the tilt grip on engine cover and raise

outboard slightly. The tilt support will automat-

ically disengage. Slowly lower outboard to its

normal operating (RUN) position.

Operate outboard in normal

operating position with tilt/run lever in the

RUN position.

1. TILT position

007022

1. Tilt grip

007023

1. Tilt support bracket

007025

WARNING

Leave tilt/run lever in the TILT position

while outboard is tilted. If the tilt/run

lever is moved to the RUN position, the

tilt support bracket can release and the

outboard could drop down unexpect-

edly.

1. RUN position

007024

NOTICE

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды