Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 27

Страница: 27 / 60



ILTING

AND

RIM

IMPACT DAMAGE PROTECTION

Your outboard has a shock absorption system

designed to help withstand damage from im-

pact with underwater objects at low to moder-

ate speeds. High speed impacts with rigid

underwater objects like pilings or boulders

can be beyond the capability of the absorption

system. Such impacts can result in serious

damage to your outboard and injury to boat

occupants from the outboard or its parts en-

tering the boat. Occupants can also be eject-

ed or injured by falling against portions of the

boat as a result of rapid deceleration following

impacts.
When boating in unfamiliar, shallow, or de-

bris-laden waters, seek information on safe

boating areas and navigation hazards from a

reliable local source. Reduce your speed and

keep a sharp lookout!

IMPORTANT:

Impact damage is NOT cov-

ered by the outboard warranty.

The outboard’s shock absorp-

tion system does not work while operat-

ing in reverse. If you back into an object,

either in the water or while trailering, your

boat and outboard can be seriously dam-

aged.

If you hit any object:
• STOP immediately and examine the out-

board for loosening of attaching hardware.

• INSPECT for damage to swivel and stern

brackets, and steering components.

• EXAMINE the boat for structural damage.

• TIGHTEN any loosened hardware.
If the collision occurred in the water, proceed

slowly to harbor. Before boating again, have

your Dealer thoroughly inspect all compo-

nents.

WARNING

Failure to inspect for damage after an

accident or striking an object could

result in sudden, unexpected component

failure, loss of boat control, and per-

sonal injury. Unrepaired damage could

reduce your boat and outboard’s ability

to resist future impacts.

007021

NOTICE

DR4412

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды