Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 3

Страница: 3 / 60

Easy to Own and Operate

• Multi-Fuel Capable

• De-Watering System

• Low Reflection Paint and Decals

• One-Year Limited Warranty

• No Operational Break-In Procedure

• Easy Starts (no choking or priming)

• Self Flushing Cooling System

• Simplified Winterization Procedure

• Digital Diagnostics

Durable and Reliable

• Full Corrosion Protection

• Multi-Point Lubrication System

• Auto-Calibrated Linkage

• Robust, Heavy-Duty Design

• Posi-Lock Latches

• Extra Capacity Water Pump

• Iridium Spark Plugs

• Vibration Isolated Electronics

• Stainless Steel Thermostat

• Nickel/Chrome-Faced Piston Rings

• Micro Finished Connecting Rods/Crankshaft

•

MFE S.A.F.E.

Warning System—maximum

engine operation in critical situations

Cleaner and Quieter

• EPA Emissions Compliance

• European Union Emissions Compliance

• Sealed Fuel System

• Low Friction Design (No powerhead

gears, belts, cams, oil scraping rings,

or mechanical oil pump)

• Full Length Insulated Lower Pans

• Quiet Signature Sound

• Air Intake/Silencer

• Idle Air Bypass

FEATURES AT A GLANCE

The following trademarks are the property of Bombardier Recreational Products Inc. or its affiliates:

Evinrude®

Evinrude® MFE

I-Command

™

Evinrude® E-TEC®

2+4™ Fuel Conditioner

S.A.F.E.

™

Evinrude®/Johnson® Genuine Parts

Evinrude®/Johnson® XD100™

SystemCheck

™

BRP Logo

HPF Pro™

Gearcase Lubricant

Triple-Guard™

Grease

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды