Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 10

Страница: 10 / 60

DECLARATION OF CONFORMITY

• Application of Council Directives and their relevant harmonized standard(s):

Recreational Craft Directive 94/25/EC as amended by 2003/44/EC

•EN ISO 8178-1:1996

•EN ISO 14509

Electromagnetic Compatibility Directive 2004/108/EC

•EN 55012:2007

•EN 61000-6-1:2007

•EN 61000-4-2:2008

•EN 61000-4-3:2006

Machinery Directive 2006/42/EC

•ISO 12100:2010

• Product Type:

Marine Outboard 2-Stroke Cycle SI Engine sold under the

Evinrude

name

I, the undersigned, hereby declare that the product conforms to the above Directive(s) and

Standard(s).

George Broughton
Director of Engineering – Outboards

Manufacturer:

Authorized Representative:

BRP US Inc

BRP Europe N.V.

10101 Science Drive

Geert De Brandt, Operations Manager

Sturtevant, WI, USA 53177

Skaldenstraat 125
Gent, Belgium, B-9042

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды