Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 42

Страница: 42 / 60

Maintenance

3) Remove propeller and place the shift lever

in NEUTRAL position.

4) Connect garden hose to flushing device

and install flushing device on gearcase.

5) Turn on the water. Keep the water pres-

sure between 20 and 40 psi (140 to

300kPa).

6) Start the engine and RUN AT IDLE

SPEED. Flush engine for at least five min-

utes. A steady stream of water must flow

from exhaust relief port of outboard.

7) Turn engine OFF. Leave the outboard in

vertical position long enough to completely

drain the powerhead.

SPARK PLUGS

The ignition system

presents a serious shock hazard. Use

caution to avoid injury from shock or

injury resulting from your reaction to

shock. Do not handle primary or

secondary ignition components while the

engine is cranking or running.

Spark plugs should be serviced by qualified

personnel. Incorrect spark plug maintenance

can lead to engine damage.

Replacement spark plugs

MUST be indexed correctly.

Marine Engine Duty Cycles

The International Council of Marine Industry

Associations (ICOMIA) Standard No. 36-88

specifies a marine engine duty cycle based on

documented studies. A duty cycle is a profile

of engine running and usage. This duty cycle

is used to determine average spark plug lon-

gevity and maintenance requirements for

Evinrude E-TEC

outboards.

Some running profiles and

conditions can lead to spark plug wear

sooner than expected. Depending on your

specific usage, the spark plug mainte-

nance schedule may require adjustment.

SUBMERGED OUTBOARD

If your outboard has been under water,

have

it serviced immediately upon recovery

. If

immediate service is unavailable, re-sub-

merge it in fresh water to avoid prolonged ex-

posure to the atmosphere.
After submersion, all boat and engine electri-

cal, fuel, and oiling systems must be inspect-

ed for signs of water intrusion. A qualified

technician should perform this service.

1. Flushing device
2. Stream of water

008032

CAUTION

NOTICE

ICOMIA Marine Engine Duty Cycle

Engine Speed as

Percentage of Rated

Speed (RPM)

Time at Specified RPM

(Percentage of total

engine running time)

IDLE

40%

25%

60%

15%

80%

14%

100%

NOTICE

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды