Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 26

Страница: 26 / 60

Using The Evinrude MFE Outboard

Tilt Pin

To adjust the trim angle:
Place the outboard in full TILT position. Refer

Tilt UP

on page 22.

• Grasp the tilt pin retainer and squeeze to re-

lease. Slide tilt pin all the way out.

• Insert tilt pin in desire position. Make sure

the trim angle adjustment rod passes

through both stern brackets.

• Push in against retainer to lock in place.

Make sure the tilt pin is locked on the stern

bracket.

SHALLOW WATER DRIVE

Tilt the outboard to any position within the tilt

range for shallow water operation.

When operating a tilted out-

board, do not run above idle speed. Keep

the water intakes submerged at all times

to prevent the engine from overheating.

Engaging Shallow Water Drive

Slow the engine and shift to NEUTRAL before

engaging or disengaging shallow-water drive.

Move tilt/run lever to TILT position.
Grasp tilt grip on engine cover and tilt out-

board until shallow water drive link engages

tilt pin.
Relocate the tilt pin if necessary. Refer to

Tilt

Pin

on page 24.

When operating a tilted out-

board, do not run above idle speed. Keep

the water intakes submerged at all times

to prevent the engine from overheating.

Disengaging Shallow Water Drive

Move tilt/run lever to RUN position. Grasp tilt

grip on engine cover and raise outboard

slightly. The shallow water drive link will auto-

matically disengage. Slowly lower outboard to

its normal operating position.

1. Tilt pin retainer
2. Tilt pin

007025

WARNING

When in shallow water drive, your motor

has no protection from the effects of

underwater impact.
Operate the motor in FORWARD and

ONLY at slow speed. The motor can tilt

up forcibly and drop suddenly if it hits an

underwater object or if you shift to

REVERSE and apply throttle. You could

lose control.

NOTICE

1. Shallow water drive link

007025

1. Water intakes

007069

NOTICE

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды