manualshive.com logo in svg

Evinrude 30 HORSEPOWER MFE, Руководство оператора, Страница: 35 / 60

Поделиться
Скачать
Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 35

33

TRANSPORTING THE OUTBOARD

TRAILERING

Trailer your boat with the outboard in a verti-

cal position. If your trailer does not provide ad-

equate road clearance, tilt the outboard as

needed and support the outboard with an ac-

cessory trailering bracket.

The outboard must be

restrained when trailering. Bouncing dur-

ing transport may damage the outboard

and the boat’s transom.

Use of the tilt support bracket

or tilt lock lever when trailering may

cause damage to the outboard.

Use of the steering friction

adjustment screw to position the out-

board for trailering may cause damage to

the outboard.

TRANSPORTING / STORAGE

If the outboard is laid down for transportation

or storage it should be laid on its back. 

IMPORTANT: 

The oiling system must be

primed before reusing the outboard. Refer to

Priming the Oil System

 on page 16.

If the engine is transported laying on its side,

protect the motor covers, by laying it on an old

blanket or other soft cloth.

A

 WARNING

If engine is equipped with a quick-dis-

connect fuel hose, you MUST disconnect

the fuel hose from the engine and the

fuel tank to prevent fuel leaks:

• Whenever the engine is NOT being

used

• Whenever the engine is being

trailered

• Whenever the engine is in storage

A small amount of fuel may be released

when the fuel connector is discon-

nected.
Always wipe off any fuel spillage.
Store portable fuel tanks in well-venti-

lated areas, away from heat sources and

open flames. Close the vent screw of the

fuel tank cap, if equipped, to prevent

escape of fuel or fuel vapors which could

accidentally ignite. Do not allow discon-

nected fuel hoses to leak fuel.

NOTICE

NOTICE

1. Steering friction adjustment screw

008926

1. Transport outboard resting on bum-

pers

007043

NOTICE

1

1

Содержание 30 HORSEPOWER MFE





























































Отзывы:

Нет отзывов