Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 17

Страница: 17 / 60



UEL

AND

OIL REQUIREMENTS

Evinrude/Johnson XD100

is the ONLY

outboard oil recommended for use with

Evinrude MFE

outboards.

Evinrude/Johnson

XD100

outboard oil MUST be used when

outboard is run on heavy fuels.

Evinrude/

Johnson XD100

oil MUST be used when

operating in temperatures under 32°F (0°C).
In combat emergency if

Evinrude/Johnson

XD100

oil is not available, you must use an oil

that meets NMMA TC-W3 certification stan-

dards. Operating time should be limited to the

duration of the combat emergency and the

operator should return to operating on

Evin-

rude/Johnson XD100 as soon as possible.

IMPORTANT:

Failure to follow oil specifica-

tions could void the engine warranty if a lubri-

cation-related failure occurs.

Filling the Oil Tank

Release rear engine cover latch by pulling the

handle back and turning downward.

Pull up on the tilt handle to release the engine

cover seal on the engine cover.

Release the hook from its catch in the front

and remove the engine cover to access the oil

tank.

Remove the filler cap and fill the tank with the

recommended outboard lubricant, as speci-

fied in

Oil Requirements

on page 15.

Replace the filler cap and tighten securely.

Reinstall the engine cover.

IMPORTANT:

The oil tank capacity is 1.5

quarts (1.4 liters).

007000

1. Tilt handle

007001

007002

007003

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды