Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 49

Страница: 49 / 60



NSTALLATION

INSTALLING THE OUTBOARD

IMPORTANT:

Follow all directions carefully.

The outboard’s warranty will not cover prod-

uct damage or failure that results from incor-

rect outboard installation.
Refer to

Priming the Oil System

on page 16.

Mounting

Center the outboard on the transom (or

mounting bracket) and tighten clamp screws

by hand.
Use the outboard stern brackets as a tem-

plate for location and size of holes to drill in

the transom.
Use each stern bracket’s mounting holes as a

guide to drill 5/16 in. (7.9 mm) holes through

the transom. Drill two (2) mounting holes.

Install the mounting bolts through the stern

brackets and transom. Install large washers

and locknuts onto bolts and tighten securely.

WARNING

The outboard must be correctly

installed. Failure to correctly install the

outboard could result in serious injury,

death or property damage. We strongly

recommend that your Dealer install your

outboard to ensure proper installation.

WARNING

Even if equipped with clamp screws,

your outboard must be bolted to the boat

to prevent it from “working off the tran-

som” during operation.

1. Drilled transom holes

007040

1. Large washers
2. Bolts

18961

WARNING

When replacing bolts, screws, or other

fasteners, use

Evinrude/Johnson

parts

or parts of equivalent strength and mate-

rial.

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды