Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 16

Страница: 16 / 60

Using The Evinrude MFE Outboard

FUEL SYSTEM OPERATION

IMPORTANT:

The minimum inside diameter

of the fuel hose from the fuel tank to the out-

board must be 3/8 in. (9 mm). Be sure the

boat’s fuel system provides adequate fuel to

the outboard. Fuel systems with anti-siphon

valves, filters or primer units may restrict fuel

flow to the outboard and effect engine perfor-

mance.

FUEL SYSTEM PRIMING

If the outboard is run out of fuel, refill the fuel

tank and squeeze the primer bulb until firm.
Prime the electric fuel pump by first removing

the engine cut–off switch clip and then pulling

the rope at least two times. This will cause the

fuel pump to fill the injectors. Replace the en-

gine cut–off switch clip and follow the normal

starting procedure.

FUEL SELECTOR SWITCH

Operation with the fuel selec-

tor switch in the wrong position could

cause internal engine damage not cov-

ered by the outboard’s limited warranty

The

Engine Management Module

(

EMM

) in-

cludes programs allowing the engine to run on

several types of fuel. You MUST select the

correct program for the fuel being used. Refer

Fuel Requirements

on p. 13.

• To use jet fuel, or kerosene, press the fuel

selector switch

• To use gasoline, pull the fuel selector switch

OUT

to expose the red indicator ring.

When switching from one fuel to another:
• Connect the fuel supply hose to the desired

fuel supply.

• Adjust the selector switch on the port side of

the outboard for the new fuel.

• Restart the engine to reset the

EMM

—

changing the switch has no effect while the

engine is running.

• The

EMM

calculates when the previous fuel

remaining in the engine has been used and

switches the program at that time.

• The engine may run noticeably rough during

the transition period.

IMPORTANT:

Diesel fuel should be used as

an emergency fuel ONLY. If diesel fuel must

be used, the fuel selector switch should be in

the Heavy Fuel position. Refer to

Emergency

Fuel

on p. 13 and

De-Carboning Procedure

on p. 38.

WARNING

If engine is equipped with a quick-dis-

connect fuel hose, you MUST discon-

nect the fuel hose from the engine and

the fuel tank to prevent fuel leaks:
• Whenever the engine is NOT being

used

• Whenever the engine is being trailered

• Whenever the engine is in storage
NOTE: A small amount of fuel may be

released when the fuel connector is dis-

connected.
Store portable fuel tanks in well-venti-

lated areas, away from heat sources and

open flames. Close the vent screw of the

fuel tank cap, if equipped, to prevent

escape of fuel or fuel vapors which

could accidentally ignite. Do not allow

disconnected fuel hoses to leak fuel.

006550

NOTICE

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды