Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 44

Страница: 44 / 60

Maintenance

LONG-TERM STORAGE
(WINTERIZATION)

Winterization prepares your outboard for

long-term off-season storage. During winter-

ization, the engine is “fogged” and extra oil is

used to coat internal engine components.

Note:

The Long-Term Storage procedure can

be used to prime the oiling system.
Winterization requires a specific process of

steps.
Closely follow the applicable winterization

procedure for your outboard:
• Remote control

• Tiller control

• Remote control with foot throttle
If you are unsure which procedure is right for

you, contact your Dealer for assistance.
You can confirm your outboard enters winter-

ization mode when the engine runs at fast idle

and:
• The

SystemCheck

gauge lights flash (if

equipped).

• The

I-Command

gauge displays winteriza-

tion message (if equipped).

Preparation

Your outboard can be winterized in the water.

If winterizing in water,

make sure the water

intake screens are completely submerged.
1) Stabilize the engine’s fuel supply. Add

2+4

Fuel Conditioner

following instructions on

container. Fill fuel tank.

If winterizing on a trailer,

remove the pro-

peller. Attach a garden hose to flushing

port and turn on the water. Refer to

Flush-

ing

on page 39.

3) Outboard

must

be in NEUTRAL, and re-

mote control and shift linkage must be in

NEUTRAL position at all times during win-

terization procedure.

Winterizing Procedure

1) Fully advance throttle grip. Start the out-

board. Outboard runs at slow idle speed.

2) After outboard runs for at least 15 seconds,

move throttle grip to IDLE position. Out-

board continues to run at slow idle speed.

WARNING

Outboard must be in NEUTRAL before

performing winterization. Starting out-

board in gear can cause personal injury.
If winterizing on a trailer, the propeller

must be removed before performing pro-

cedure. Failure to remove propeller can

cause personal injury or death.

Tiller Control – Typical

007036

007037M

007038

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды