Evinrude 30 HORSEPOWER MFE Скачать руководство пользователя страница 48

Страница: 48 / 60

Product Information

INSTALLATION

Use an appropriate hoist to lift

the engine. Refer to Specifications on

page 50 for engine weight.

TRANSOM HEIGHT

Make sure the transom height matches the

length of the outboard to be installed.
• A 19 to 21 in. (48.3 to 53.3 cm) transom

height uses a 20 in. (50.8 cm) shaft out-

board.

• The shaft length of the outboard being in-

stalled should come close to matching the

transom height of the boat.

• Refer to

Specifications

on page 50 for

transom height.

Determine transom height by measuring from

the top edge of the transom, along the center-

line.

Boat performance depends on outboard

mounting height.
Generally, the anti-ventilation plate of the

gearcase should align with the bottom of the

hull. Conventional V-hulls often perform well

with the anti-ventilation plate approximately 1

in. (25 mm) above the bottom of the hull.
The anti-ventilation plate should NOT extend

more than 2 in. (5 cm) BELOW the bottom of

the hull.
Test outboard and boat performance at differ-

ent heights until the best performance is

achieved.

IMPORTANT:

Be sure that outboard water

pressure is not adversely affected by the

mounting height of the outboard.

WARNING

Your outboard must not exceed the max-

imum horsepower indicated on the

boat’s capacity plate. Such overpower-

ing can cause loss of control. Contact

your Dealer or the boat’s manufacturer if

your boat lacks a capacity plate.
Boats designed for remote-steered out-

boards might be overpowered by a tiller-

steered outboard of the maximum rated

horsepower. Ask your Dealer or boat

manufacturer if you are unsure about

your boat’s suitability.
Incorrectly matched boat and outboard

transom heights can cause boat instabil-

ity and loss of control. Refer to Transom

Height.
Prevent lateral movement and possible

outboard loss by using the mounting

hardware supplied or hardware of suffi-

cient size, strength, and quality. Refer to

Installing the Outboard on page 47.
A mounting surface that is damaged or

too thin to support your outboard while

underway might fail during operation,

causing a loss of control. Be sure the

boat’s transom or mounting bracket is

structurally sound and between 1 5/8 in.

(41 mm) and 2 3/4 in. (70 mm) in thick-

ness.

NOTICE

1. Centerline
2. Antiventilation plate
3. Transom Height

007039

Содержание 30 HORSEPOWER MFE





























































Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды

Evinrude 30 HORSEPOWER MFE, Руководство оператора

Результаты поиска

Содержание 30 HORSEPOWER MFE

Отзывы:

Похожие инструкции для 30 HORSEPOWER MFE

Бренды по названию

Популярные бренды